52 construction toolbox talks: a free year of weekly safety talks
A toolbox talk is a short safety meeting held on the job site, usually at the start of a shift. This page gives you 52 talks, one for each week of the year, grouped by hazard. Each has key points, questions for the crew and the OSHA standard or guidance behind it. A printable sign-in sheet is included.
What a toolbox talk is
A toolbox talk is a short safety meeting at the work area. The foreman or a lead worker runs it. It covers one topic and takes about 10 minutes. Some crews call it a tailgate meeting, because it often happens at the back of a truck.
A good talk ties one hazard to today's work. "Ladders" is a topic. "The extension ladder we're setting at the east wall this morning" is a toolbox talk.
Toolbox talks don't replace formal training. OSHA 10 and 30 courses, competent person training and equipment operator training still matter. A weekly talk keeps the rules fresh between those trainings. It also gives the crew a regular time to raise hazards.
Why GCs ask for toolbox talk records in prequalification
A GC's prequal form looks at your safety record from two sides. Your experience modification rate (EMR) and your OSHA 300A summaries show results. Your written safety program and training records show the habits behind those results. Toolbox talk sign-in sheets are the easiest training record to produce, because you make a new one every week.
Prequal questionnaires often ask whether you hold toolbox or tailgate safety meetings, and how often. Some GCs also ask for recent sign-in sheets or set a talk schedule in the subcontract.
There are three reasons GCs care.
- OSHA requires training. Under 29 CFR 1926.21(b)(2), the employer must instruct each employee to recognize and avoid unsafe conditions and to know the rules for their work. A signed sheet shows the training happened, when, and who was there.
- Some standards require written proof. Fall protection training needs a written certification record with each worker's name, the training date and the trainer's signature, under 29 CFR 1926.503(b). A toolbox talk alone may not meet a standard's full training rule. The sheet still shows what you covered and when.
- GCs share responsibility on site. Under OSHA's multi-employer citation policy, a GC can be cited as the controlling employer. OSHA expects a controlling employer to use reasonable care to prevent and detect violations. The policy says a GC may inspect less often where a sub shows strong signs of effective safety efforts. Steady toolbox talk records are one way to show those efforts.
What a GC looks for in your sheets
- Talks on a regular schedule, with no long gaps.
- Topics that match your trade and the work on that job.
- A named presenter on every sheet.
- Every crew member's printed name and their own signature.
- Follow-up after an incident or near miss.
How to run a good 10-minute talk
Ten minutes is enough for one topic if you plan it. Here is a simple order.
- Prepare the day before. Pick the talk. Read it once. Know which task on this job it applies to.
- Start on time, at the work area. Do it before the tools come out. Stand where the crew can see the hazard.
- One minute on why. Name the task today that has this hazard.
- Five minutes on the key points. Read them aloud. Show the gear. Point at the edge, the cord or the trench.
- Three minutes on questions. Ask the crew the questions in the talk. Wait for answers. Let a worker show the right way.
- One minute to close. Repeat the one thing to remember. Pass the sign-in sheet.
A few habits make talks work better.
- Speak the language your crew understands best. OSHA's training policy statement says employers must instruct workers in a language and vocabulary they understand.
- Keep to one topic. A second topic can wait for next week.
- Fix what comes up. If a worker names a hazard, write it on the sheet, fix it, and tell the crew it's fixed.
- Rotate presenters. A worker who leads a talk learns the topic best.
How to document attendance
Every talk gets a sign-in sheet. A complete sheet shows:
- the date and start time;
- the company and job site;
- the topic, and the OSHA standard if there is one;
- the presenter's name and signature;
- each attendee's printed name and signature;
- any hazards or questions the crew raised.
Then follow these rules.
- Workers sign their own names. Never sign for someone else.
- If someone misses the talk, cover it with them before they start the task. Have them sign and write the date they were caught up.
- File the sheet the same week. Scan or photograph it and save it by job and date. Keep the paper too if your company or the GC asks for it.
- Keep sheets for at least five years. OSHA has no single retention rule for toolbox talk sheets. Five years matches how long OSHA requires you to keep the 300 log and 300A summary under 29 CFR 1904.33.
Use the printable sign-in sheet on this page. It prints on one page with room for 20 names.
How to pick topics: seasonal, by trade, and after an incident
Mix three sources. Use the season, your trade's hazards, and anything that just went wrong.
By season
- Start heat talks in spring, before the first hot week. OSHA says workers need extra protection during the first warm days of spring or early summer.
- Start cold, ice and short-day talks in late fall.
- Give fall protection talks in May. OSHA's National Safety Stand-Down to Prevent Falls in Construction ran May 4 to 8 in 2026.
- Give trench talks in June. NUCA's Trench Safety Stand Down ran June 15 to 19 in 2026.
- Give the mental health talk in September. OSHA notes that September is Suicide Prevention Month.
By trade
Weight the year toward your own hazards. A roofer needs more fall and heat talks. An electrician needs more lockout and GFCI talks. A concrete crew needs more silica talks. Match the GC's site safety plan too. If the plan flags a hazard on that job, give a talk on it before the work starts.
| Trade | Start with these talks |
|---|---|
| Roofing | 1, 2, 3, 4, 5, 23, 39 |
| Framing | 1, 3, 5, 8, 37, 38 |
| Concrete | 19, 20, 21, 22, 30, 43 |
| Masonry | 8, 9, 20, 21, 41 |
| Electrical | 7, 10, 14, 15, 16 |
| Plumbing and HVAC | 5, 11, 12, 13, 21, 39 |
| Painting and drywall | 7, 8, 10, 31, 32, 33 |
| Excavation and site work | 11, 12, 13, 19, 43, 44 |
The free OSHA safety program template does this for you. It builds a year of weekly toolbox talks from the tasks you pick, with heat and cold talks in season.
After an incident or near miss
- Give a talk on it at the next start of shift. Don't wait for the calendar.
- Stick to the facts. Say what happened, what the hazard was and what changes now. Don't blame a person in front of the crew.
- Ask the crew what else could go wrong the same way.
- Note the talk on the incident report. If the injury is recordable, it also goes on the OSHA 300 log. Our OSHA 300A guide explains the log and the summary.
- Then go back to the calendar.
A sample year
Here is one way to spread the 52 talks across a year. Numbers link to each talk below.
| Month | Why | Talks |
|---|---|---|
| January | Ice, and a fresh start on emergency plans and PPE | 27, 46, 49, 28 |
| February | Indoor work, cords and chemicals | 50, 14, 32, 33 |
| March | Spring cleanup and ladders | 40, 5, 6, 7, 41 |
| April | Silica, as cutting picks up | 20, 21, 22, 31 |
| May | First warm days, and the falls stand-down | 23, 24, 1, 2 |
| June | Heat, and the trench stand-down | 25, 11, 12, 13, 3 |
| July | Fall rescue and scaffolds | 4, 8, 9, 10 |
| August | Power lines and equipment | 15, 16, 43, 44 |
| September | Suicide Prevention Month, traffic and struck-by | 52, 45, 17, 18, 19 |
| October | Tools | 35, 36, 37, 38 |
| November | Fire and flammables before heaters come out | 34, 39, 48, 29 |
| December | Cold, dark and the end-of-year rush | 26, 42, 30, 47, 51 |
The 52 talks
Each talk opens to show its key points, questions for the crew and the OSHA standard. Jump to a theme.
Falls and ladders · Scaffolds · Excavation and trenching · Electrical · Struck-by and caught-between · Silica and dust · Heat and cold · PPE · Hazard communication · Tools and equipment · Housekeeping · Vehicles and backing · Emergency and first aid · Health
These talks put OSHA standards in plain words. They are not legal advice and don't replace the standard. Check the current text at osha.gov. States with their own OSHA plans can have stricter rules. PreQualifySubs.com is not affiliated with or endorsed by OSHA.
Falls and ladders
1. Guardrails, covers and edges 1926.501, 1926.502
- For most work surfaces, construction fall protection starts at 6 feet above a lower level. Guardrails, safety nets or a personal fall arrest system meet the rule. Scaffolds start at 10 feet.
- The top rail sits 42 inches high, plus or minus 3 inches. It must hold at least 200 pounds of force.
- Midrails go halfway between the top rail and the walking surface.
- A hole is any gap 2 inches or more at its narrowest. A cover must hold at least twice the weight of the workers, equipment and materials that could be on it.
- Secure every cover so wind, equipment or people can't move it. Mark it HOLE or COVER, or color code it.
Ask the crew. Where on this job is there an open edge or hole we haven't protected? If you pull a guardrail to land material, who puts it back?
OSHA standard. 29 CFR 1926.501(b)(1), 29 CFR 1926.502(b) and (i), 29 CFR 1926.500(b)
2. Inspecting your harness and lanyard 1926.502(d)
- Inspect your harness, lanyard and connectors before each use.
- Look for cuts, frays, burns, broken stitching, chemical damage and bent or cracked hardware. Damaged parts come out of service.
- Gear that has stopped a fall comes out of service right away. A competent person must inspect it before anyone uses it again.
- Body belts are not allowed for fall arrest. Wear a full body harness.
- Adjust the straps so the harness is snug. Follow the maker's fit instructions.
Ask the crew. When did you last look closely at your lanyard and its hooks? What would you do if your snap hook didn't close all the way?
OSHA standard. 29 CFR 1926.502(d), (d)(19) and (d)(21)
3. Anchors and tie-off points 1926.502(d)(15)
- A fall arrest anchor must hold 5,000 pounds for each worker attached. The other option is an anchor a qualified person designs with a safety factor of at least two.
- The anchor must be separate from any anchor that holds up a platform.
- A guardrail is built for 200 pounds of force. It is not a fall arrest anchor.
- Rig your system so you can't free fall more than 6 feet or hit a lower level. Check the clearance below you before you tie off.
- Tie off overhead when you can. Tying off at your feet adds to your free fall.
Ask the crew. Point to the anchor you're using today. Who says it's rated? How far would you drop here before your lanyard stopped you?
OSHA standard. 29 CFR 1926.502(d)(15) and (d)(16)
4. Fall rescue: suspension trauma 1926.502(d)(20)
- OSHA requires prompt rescue after a fall, unless workers can rescue themselves.
- A worker hanging in a harness can pass out as blood pools in the legs. OSHA's bulletin on suspension trauma calls this potentially life threatening. It cites research showing unconsciousness and death in less than 30 minutes.
- Plan the rescue before work starts. Know who calls 911, what lift or ladder reaches the worker, and who is trained to use it.
- If you're hanging and can't get down, pump your legs. Push against a foothold or relief strap.
- After rescue, a health care professional checks the worker, even if they feel fine.
Ask the crew. If someone fell and hung from a lanyard right now, how would we get them down? Where is the lift or ladder we would use?
OSHA standard. 29 CFR 1926.502(d)(20). Guidance: OSHA SHIB 03-24-2004, Suspension Trauma/Orthostatic Intolerance
5. Ladder inspection and setup 1926.1053
- A competent person inspects ladders on a regular basis and after anything that could damage them. Look yours over before you climb.
- Mark a broken ladder "Do Not Use" and take it out of service until it's fixed.
- An extension ladder's side rails go at least 3 feet above the landing.
- Set the foot out about one-quarter of the ladder's working length. That's 1 foot out for every 4 feet of ladder up to the top support.
- Set ladders on stable, level ground, or secure them. Use each ladder only for what it was designed for.
Ask the crew. What was wrong with the last ladder you used? Is there a damaged ladder in anyone's truck right now?
OSHA standard. 29 CFR 1926.1053(b)(1), (b)(4), (b)(5)(i), (b)(6), (b)(15) and (b)(16)
6. Three points of contact 1926.1053(b)(20) to (22)
- Face the ladder going up and coming down.
- OSHA requires at least one hand on the ladder as you climb. Three points of contact goes further. Keep two hands and a foot, or two feet and a hand, on the ladder.
- Don't carry anything that could make you lose your balance. Use a tool belt or a haul line.
- Keep your belt buckle between the rails. If you can't reach, climb down and move the ladder.
Ask the crew. What do we carry up ladders that should go up on a rope? When did you last see someone overreach?
OSHA standard. 29 CFR 1926.1053(b)(20), (b)(21) and (b)(22)
7. Stepladders: no top step 1926.1053(b)(13)
- Never stand on the top or the top step of a stepladder.
- Open the stepladder fully and lock the spreaders before you climb.
- Don't lean a closed stepladder against a wall and climb it. It isn't designed for that.
- If you need the top step, you need a taller ladder or a lift.
Ask the crew. Is there a task on this job where people stand on the top step? What ladder or lift should we bring instead?
OSHA standard. 29 CFR 1926.1053(b)(4) and (b)(13)
Scaffolds
8. Scaffold inspection before each shift 1926.451(f)(3)
- A competent person inspects the scaffold for visible defects before each shift. They inspect it again after anything that could affect it.
- Look for missing guardrails, damaged planks, loose ties, missing base plates or mudsills, and bent frames.
- Workers more than 10 feet up on a scaffold need fall protection.
- If the site uses scaffold tags, read the tag before you climb.
Ask the crew. Who is the competent person for this scaffold today? What would make you stay off it?
OSHA standard. 29 CFR 1926.451(f)(3) and (g)(1)
9. Scaffold access and planking 1926.451(b), (e)
- When a platform is more than 2 feet above or below the access point, use a ladder, stair tower, ramp or other approved access.
- Never climb the cross braces.
- Fully plank or deck every working platform. Gaps between planks are no more than 1 inch, unless the employer can show a wider gap is needed.
- Keep scaffolds and conductive materials at least 10 feet from uninsulated power lines under 50 kV. Higher voltages need more room.
Ask the crew. How do you get up to the platform on this scaffold? Is there a gap or short plank you'd fix before you step on?
OSHA standard. 29 CFR 1926.451(b)(1), (e)(1) and (f)(6)
10. Aerial lift tie-off and pre-use check 1926.453(b)(2)
- Test the lift controls each day before use.
- Only authorized people run the lift.
- Stand on the floor of the basket. Don't sit or climb on the rail. Don't use planks or ladders in the basket to gain height.
- Clip your lanyard to the boom or basket. Never tie off to a nearby pole, structure or other equipment.
- If your lanyard could let you fall out of the basket, wear a full body harness. A body belt is not allowed for fall arrest.
Ask the crew. What's on your check before you go up? Where do you clip in on the lift we're using?
OSHA standard. 29 CFR 1926.453(b)(2), 29 CFR 1926.502(d)
Excavation and trenching
11. Trench protective systems: 5 ft rule 1926.652, 1926.651(k)
- A trench 5 feet or deeper needs a protective system, unless it's entirely in stable rock. That means sloping, benching, shoring or a shield such as a trench box.
- A trench under 5 feet still needs protection unless a competent person checks the ground and finds no sign of a possible cave-in.
- A competent person inspects the trench daily before work starts, as needed during the shift, and after rain or anything else that raises the hazard.
- If the competent person finds a hazard, everyone gets out until it's fixed.
- Never stay in a trench box while it is being installed, removed or moved up or down.
Ask the crew. Who is our competent person for this excavation? What would make you climb out right away?
OSHA standard. 29 CFR 1926.652(a)(1) and (g)(1), 29 CFR 1926.651(k)
12. Call 811 before you dig 1926.651(b)
- Before you open an excavation, find out where underground utilities are likely to be.
- Contact the utility owners and ask them to mark their lines. In the US, calling 811 reaches your local one-call center. The call and the marking are free.
- State law sets how far ahead you call. PHMSA says states require 48 to 72 hours.
- Marks show roughly where a line is. As you dig close, find the exact spot by safe means, such as careful hand digging.
- Protect, support or remove exposed lines while the excavation is open.
Ask the crew. Where are the marks on this site, and who checked them? What do you do if you hit a line nobody marked?
OSHA standard. 29 CFR 1926.651(b)
13. Ladders in trenches and spoil piles 1926.651(c), (j)
- Trenches 4 feet or deeper need a ladder, stairway, ramp or other safe way out.
- You should never have to walk more than 25 feet sideways to reach it.
- Keep spoil piles, materials and equipment at least 2 feet back from the edge, or hold them back with a retaining device.
- If a bad atmosphere could exist, test the air before anyone enters a trench deeper than 4 feet.
- Don't work in a trench where water is collecting unless precautions are in place.
Ask the crew. Where is the nearest way out from where you'll work? Is anything piled closer than 2 feet to the edge right now?
OSHA standard. 29 CFR 1926.651(c)(2), (g)(1), (h)(1) and (j)(2)
Electrical
14. GFCIs and cord inspection 1926.404(b)(1), 1926.416(e)
- Temporary 120-volt, 15- and 20-amp outlets in use on a job site need GFCI protection. The other option is a written assured equipment grounding conductor program.
- Look over cords, plugs and tools before each day's use.
- Don't use worn or frayed cords. Don't use a plug with the ground pin missing.
- Don't staple cords, hang them from nails or hang them by wire.
- Keep cords out of walkways and work spaces.
Ask the crew. Show me the last cord you threw away. What was wrong with it? Where are the GFCIs on this site?
OSHA standard. 29 CFR 1926.404(b)(1), 29 CFR 1926.416(b)(2) and (e)
15. Overhead and buried lines 1926.416(a), 1926.1408
- Before work starts, find out where energized lines are, overhead and underground. Ask, look and use instruments.
- Don't work close enough to touch a power line with your body, a tool or material. The line must be deenergized and grounded, or guarded, first.
- Treat every overhead line as energized until the owner says otherwise and it is visibly grounded.
- A crane that could get within 20 feet of a power line needs one of OSHA's power line options in place before work starts.
- Near exposed live parts, use ladders with nonconductive side rails.
Ask the crew. Where are the overhead lines on this site? What do we carry that is long enough to reach them?
OSHA standard. 29 CFR 1926.416(a), 29 CFR 1926.600(a)(6), 29 CFR 1926.1408, 29 CFR 1926.1053(b)(12)
16. Lockout/tagout: test before touch 1926.417
- Tag the controls you shut off for the work.
- Make deenergized circuits inoperative. Put tags at every point where they could be turned back on.
- Tags say plainly which equipment or circuit is being worked on.
- Test before you touch. Check your tester on a known live source first. Treat parts as live until the test shows they're dead.
- Never remove someone else's lock or tag.
Ask the crew. Where are all the places this circuit could be turned back on? What tester do we use, and how do you know it works?
OSHA standard. 29 CFR 1926.417
Struck-by and caught-between
17. Staying out from under the load 1926.1425
- Plan hoisting routes that keep loads away from people.
- Stay out of the fall zone of a suspended load.
- The only people allowed in the fall zone are those hooking, unhooking or guiding the load, making the first attachment, or running a concrete hopper or bucket.
- Use a tag line to guide a load. Never put your body under it.
- Stay out of the area the crane's counterweight swings through. Respect the barricades.
Ask the crew. Where is the fall zone for today's lifts? Who is the signal person?
OSHA standard. 29 CFR 1926.1425
18. Falling objects from above 1926.501(c), 1926.252
- Anyone exposed to falling objects wears a hard hat.
- The employer also uses toeboards, screens or guardrails to stop things falling. A canopy or a barricaded area below also meets the rule.
- Keep materials and tools back from edges.
- Don't throw debris down. Use an enclosed chute for drops of more than 20 feet outside the building.
- If debris goes down through a floor hole without a chute, barricade the area below. The barricade is at least 42 inches high and 6 feet back from the edge of the opening above.
Ask the crew. Who is working above us this week? Where are the barricades for the area below them?
OSHA standard. 29 CFR 1926.501(c), 29 CFR 1926.252(a) and (b)
19. Blocking raised blades, buckets and beds 1926.600(a)(3)
- Never work under or between equipment held up by slings, hoists or jacks unless it's blocked or cribbed.
- Fully lower or block blades, buckets and dump beds when they're not in use or being repaired.
- Put the controls in neutral, stop the motor and set the brakes, unless the work needs otherwise.
- Set the parking brake on parked equipment. On a slope, chock the wheels too.
- Stay out of pinch points between equipment and walls, or between two machines.
Ask the crew. When did you last see someone reach under a raised bed or bucket? What blocking do we keep on this site?
OSHA standard. 29 CFR 1926.600(a)(3)
Silica and dust
20. Silica: why the dust matters 1926.1153
- Cutting, drilling, grinding or crushing concrete, brick, block, mortar and stone makes respirable crystalline silica dust. OSHA says the particles are at least 100 times smaller than ordinary sand.
- Breathing it raises the risk of silicosis, lung cancer, COPD and kidney disease. OSHA calls silicosis incurable.
- OSHA's limit is 50 micrograms per cubic meter of air, averaged over 8 hours.
- The employer needs a written exposure control plan and a competent person to carry it out.
- Workers who must wear a respirator 30 or more days a year get a medical exam at no cost. It repeats at least every 3 years.
Ask the crew. Which tasks on this job make silica dust? What control do we use for each one?
OSHA standard. 29 CFR 1926.1153
21. Wet cutting and dust collection 1926.1153 Table 1
- Table 1 of the silica rule lists common tasks with the controls and respirators for each. Follow it fully, or measure and control exposure another way.
- A handheld power saw needs a built-in water system that feeds the blade nonstop. Outdoors, no respirator is needed for 4 hours or less a shift. Over 4 hours, or indoors, wear a respirator with an APF of 10.
- A drill needs a shroud with dust collection. The vacuum needs the airflow the tool maker recommends, a filter that is 99 percent efficient or better, and a filter-cleaning system.
- Use enough water to keep visible dust down. Indoors, add exhaust as needed so dust doesn't build up in the air.
- Run and maintain each tool the way the maker says. If the water or vacuum quits, stop cutting.
Ask the crew. Pick one tool we use. What does Table 1 say it needs? What do you do if the water runs out mid-cut?
OSHA standard. 29 CFR 1926.1153(c), Table 1
22. No dry sweeping or compressed air 1926.1153(f)
- Don't dry sweep or dry brush silica dust where it could add to exposure. Use wet sweeping or a HEPA-filtered vacuum.
- Don't use compressed air to clean clothes or surfaces where it could add to exposure. The exceptions are a system that captures the dust cloud, or no other method that works.
- Clean drill holes with a HEPA-filtered vacuum.
- Clean as you go, so dust doesn't build up and get kicked back into the air.
Ask the crew. What do we clean up with after a cut? Where is the HEPA vacuum, and when was its filter last changed?
OSHA standard. 29 CFR 1926.1153(f) and Table 1
Heat and cold
23. Heat illness: water, rest, shade General duty clause
- OSHA's message is water, rest and shade. They prevent heat illness and treat it.
- There is no federal OSHA heat standard in effect. OSHA uses the general duty clause and runs a heat National Emphasis Program. Some states have their own heat rules.
- OSHA's heat guide says to drink about 1 cup of water every 15 to 20 minutes. Don't drink more than 48 ounces an hour.
- Take breaks in the shade or a cool area. Move heavy work to the cooler part of the day.
- Watch each other. Early signs include thirst, irritability, a rash and cramps.
Ask the crew. Where are the water and the shade on this site today? Who is new to working in the heat this week?
OSHA guidance. OSH Act Section 5(a)(1), the general duty clause, OSHA Heat, Protecting Workers from the Effects of Heat
24. New workers and acclimatization General duty clause
- New workers need time to get used to heat. OSHA says it usually takes 1 to 2 weeks.
- OSHA and NIOSH recommend the rule of 20 percent. On day one, work 20 percent of a normal shift in the heat. Add 20 percent each day after that.
- The same protections apply to workers back from a week or more away, in the first warm days of spring and during heat waves.
- OSHA says heat deaths commonly happen on a worker's first day or first week.
- Use a buddy system. Watch new workers closely.
Ask the crew. Who on this crew is new or back from time off? How will we shorten their time in the heat this week?
OSHA guidance. OSH Act Section 5(a)(1), OSHA Heat: Protecting New Workers
25. Spotting heat stroke General duty clause
- Heat stroke is an emergency. Signs include confusion, slurred speech, passing out, seizures, a very high body temperature and a fast heart rate. The skin may be hot and dry, or the worker may sweat heavily.
- Call 911. Then cool the worker right away and keep cooling until help arrives.
- OSHA says an ice bath is the best way to cool a worker fast in an emergency. Otherwise put ice or cold wet towels on the head, neck, trunk, armpits and groin, and use fans.
- Move the worker to shade or air conditioning. Take off outer layers and heavy gear. Never leave a worker with heat illness alone.
- Heat exhaustion signs are fatigue, thirst, nausea, dizziness and heavy sweating. Stop work and cool down before it gets worse.
Ask the crew. Where would we cool a worker down on this site? What address would we give 911?
OSHA guidance. OSH Act Section 5(a)(1), OSHA Heat: Illnesses and First Aid
26. Cold stress and frostbite General duty clause
- Cold and wind pull heat from the body fast. Wind chill can cause frostbite even above freezing.
- Frostbite signs are numbness, red skin with gray or white patches, skin that feels firm or hard, and blisters.
- Hypothermia starts with shivering. Later the shivering stops. The worker gets confused, slurs speech and can pass out.
- Call 911 in an emergency. Move the worker somewhere warm, change them into dry clothes and cover the body and head. Don't rub frostbite or break blisters.
- Dress in loose layers. Wear an insulated hat, gloves and waterproof boots. Drink warm, sweet drinks, not alcohol. Take breaks somewhere warm.
Ask the crew. Where is the warm-up area on this site? Who has spare gloves and dry socks?
OSHA guidance. OSH Act Section 5(a)(1), OSHA Quick Card: Protecting Workers from Cold Stress
27. Ice, snow and slippery surfaces 1926.1052(a)(7), 1926.451(f)(8)
- Clear snow and ice from walkways and spread deicer as soon as you can after a storm.
- Wear insulated, water-resistant boots with rubber treads. Take short steps and slow down.
- Get rid of slippery conditions on stairways before anyone uses them.
- Don't work on a scaffold covered with snow or ice, except to clear it.
- Have a competent person check that a snow-covered roof or surface can hold the load before anyone goes up.
Ask the crew. Which walkways ice up first on this site? Who clears them in the morning?
OSHA standard. 29 CFR 1926.1052(a)(7), 29 CFR 1926.451(f)(8). Guidance: OSHA Winter Weather
PPE
28. Hard hats, glasses and gloves: picking the right PPE 1926.95, 1926.100
- The employer provides the PPE the hazard needs, at no cost to you. Exceptions include ordinary safety-toe boots and prescription safety glasses you can wear off the job.
- PPE must fit the person wearing it.
- Wear a hard hat wherever you could hit your head, get hit by falling or flying objects, or get an electrical shock.
- Pick gloves for the task. Cut, chemical and leather gloves protect against different things.
- If you bring your own PPE, the employer still checks that it's adequate and in good shape.
Ask the crew. What PPE does today's task need that we don't have? Is anyone's PPE worn out or the wrong size?
OSHA standard. 29 CFR 1926.95, 29 CFR 1926.100
29. Eye injuries and eyewash 1926.102, 1926.50(g)
- Wear eye or face protection against flying particles, molten metal, chemicals, gases and harmful light.
- Where things can fly, your eye protection needs side protection.
- If you wear prescription glasses, use safety glasses with the prescription built in, or ones that fit over your glasses.
- Where corrosive materials could get in your eyes, there must be a place to flush your eyes and body in the work area.
- Find the eyewash before you open the chemical. Read the first aid section of the Safety Data Sheet.
Ask the crew. Where is the nearest eyewash from where we're working? Which products on this job call for goggles, not just glasses?
OSHA standard. 29 CFR 1926.102(a), 29 CFR 1926.50(g)
30. Hearing protection: fit it right 1926.101, 1926.52
- OSHA says if you have to raise your voice to talk to someone 3 feet away, the noise may be over 85 decibels.
- OSHA's construction limit is 90 dBA averaged over 8 hours. When noise can't be brought under the limit, hearing protection must be provided and used.
- Earplugs must be fitted to each person. Plain cotton doesn't count.
- Follow the maker's instructions. For foam plugs, roll them thin, reach over your head and pull your ear up and back, then hold the plug while it expands.
- Wear protection the whole time you're in the noise.
Ask the crew. Which tools on this job make you shout to be heard? Show me how you put in your earplugs.
OSHA standard. 29 CFR 1926.101, 29 CFR 1926.52
31. Respirator seal checks and care 1910.134
- You need a medical evaluation before a fit test or before you're required to wear a respirator.
- Get fit tested before first use, with any new model or size, and at least once a year.
- Do a user seal check every time you put on a tight-fitting respirator.
- Facial hair can't come between the face and the sealing surface of a tight-fitting respirator.
- Inspect it before each use. Clean it and store it away from dust, sun, heat, moisture and chemicals.
Ask the crew. When was your last fit test? Show me a positive and a negative pressure check.
OSHA standard. 29 CFR 1910.134, which applies to construction through 29 CFR 1926.103
Hazard communication
32. Reading an SDS and a label 1910.1200(f), (g)
- Every hazardous chemical on site has a Safety Data Sheet. You must be able to get to it during every shift.
- An SDS has 16 sections in the same order. Section 2 lists the hazards. Section 4 is first aid. Section 8 covers exposure controls and PPE.
- A shipped label shows the product name, a signal word, hazard statements, pictograms, precautionary statements and the supplier's contact details.
- "Danger" marks the more severe hazards. "Warning" marks the less severe ones.
- You get trained on the chemicals in your work area when you start, and again when a new hazard comes in.
Ask the crew. Pick a product we use every day. What does section 8 say to wear? Where are the SDSs for this job?
OSHA standard. 29 CFR 1910.1200(f), (g) and (h), which applies to construction through 29 CFR 1926.59
33. Labeling secondary containers 1910.1200(f)
- Every container of a hazardous chemical at work needs a label.
- A workplace label can repeat the shipped label. Or it can show the product name plus words, pictures or symbols that give the hazards.
- A portable container you fill and use yourself right away doesn't need a label.
- If you hand it off or leave it, label it.
- Never put chemicals in drink bottles.
Ask the crew. What's in that unlabeled bucket or spray bottle? Who has blank labels on this job?
OSHA standard. 29 CFR 1910.1200(f)(6) and (f)(8)
34. Gas cans and flammable liquids 1926.152
- Store and handle flammable liquids only in approved containers. For 5 gallons or less, use an approved safety can or a DOT-approved container.
- Keep no more than 25 gallons in a room outside an approved storage cabinet.
- Shut off the engine before you fuel any equipment.
- No smoking or open flames where you fuel or dispense.
- Keep open flames and other ignition sources at least 50 feet from where flammable liquids are used.
Ask the crew. Where do we store fuel on this site? Do we shut off every engine before we fuel it?
OSHA standard. 29 CFR 1926.152(a)(1), (b)(1), (f)(3) and (g)
Tools and equipment
35. Guards stay on 1926.300
- A power tool designed for a guard must have the guard on when in use.
- Belts, gears, shafts, pulleys, chains and other moving parts are guarded where you could touch them.
- Keep every tool in safe condition, whether the company or the worker owns it.
- Tag an unsafe tool or lock its controls so it can't run. Or remove it from the work.
- Never pin back a saw guard.
Ask the crew. Where have you seen a guard pinned back or taken off? What do you do with a tool that's missing its guard?
OSHA standard. 29 CFR 1926.300(a) and (b), 29 CFR 1926.20(b)(3)
36. Grinders and cut-off wheels 1926.303
- Grinders must have their guards. Keep the guard between the wheel and you.
- Inspect every wheel closely and ring-test it before you mount it.
- The wheel must slide onto the spindle freely. Don't force it. Tighten the nut only enough to hold it.
- Check the speeds marked on the wheel and the grinder. The wheel's maximum speed must be at least the grinder's speed.
- Wear eye protection. Grinding concrete or masonry also falls under the silica rule.
Ask the crew. What's the speed on your grinder and on the wheel you're using? Has anyone taken off a guard to fit a bigger wheel?
OSHA standard. 29 CFR 1926.303(b), (c)(7), (c)(8) and (c)(9)
37. Nail gun safety 1926.302(b)
- Use full sequential trigger nail guns. NIOSH recommends them because they lower the risk of firing by accident.
- An automatic-feed nailer that runs above 100 psi at the tool must have a muzzle safety. It won't fire unless the tip is on the work.
- Keep your finger off the trigger when you're not nailing.
- Never disable or bypass the safety contact.
- Get medical care after any nail gun injury, even one that looks small.
Ask the crew. What trigger do our nailers have? Has anyone had a double fire or a nail glance off, and what happened?
OSHA standard. 29 CFR 1926.302(b)(1) and (b)(3). Guidance: NIOSH Nail Gun Safety
38. Powder-actuated tools 1926.302(e)
- Only workers trained on that tool may use it.
- Test the tool each day before loading, the way the maker says.
- Load it just before you fire. Never point it at anyone, loaded or empty. Keep your hands clear of the barrel end.
- Never leave a loaded tool unattended.
- Don't fire into very hard or brittle material like cast iron, glazed tile, glass block or hollow tile. Never use it where the air could be explosive or flammable.
Ask the crew. Who on this crew is trained on our powder-actuated tool? What's on the other side of the material you're shooting into?
OSHA standard. 29 CFR 1926.302(e)
39. Hot work: clear the area and fire watch 1926.352, 1926.350
- Move anything that can burn away from the hot work. If it can't move, shield it.
- No hot work where flammable paint, flammable compounds or heavy dust create a hazard.
- Keep a suitable fire extinguisher ready in the work area.
- Post a fire watch when normal precautions aren't enough. The watch stays long enough after the work to be sure nothing is burning.
- Keep gas cylinders upright and secured, with valve caps on when you move or store them. Store oxygen 20 feet from fuel gas, or behind a noncombustible barrier at least 5 feet high with at least a half-hour fire rating.
Ask the crew. What's below and behind us that sparks could reach? Who is on fire watch, and for how long after we stop?
OSHA standard. 29 CFR 1926.352, 29 CFR 1926.350(a)
Housekeeping
40. Housekeeping and slips, trips and falls 1926.25
- Keep work areas, walkways and stairs clear of scrap lumber with nails and other debris.
- Remove combustible scrap on a regular schedule.
- Use containers for trash and oily rags. Containers for oily, flammable or hazardous waste need covers.
- Pull or bend over nails in scrap lumber.
- Clean up as you go, not just at the end of the day.
Ask the crew. What's the worst trip hazard on this site right now? Who owns cleanup in each area?
OSHA standard. 29 CFR 1926.25
41. Material storage and stacking 1926.250
- Stack, rack, block or interlock stored materials so they can't slide, fall or collapse.
- Keep aisles and passageways clear.
- Inside a building under construction, keep materials at least 6 feet from a hoistway or floor opening. Keep them 10 feet from an exterior wall that doesn't reach above the stack.
- Keep brick stacks to 7 feet or less. Pull nails from used lumber before you stack it.
- Don't overload floors. Follow the posted load limits.
Ask the crew. Is anything stored near an opening or an edge right now? Which stack on this site would you not walk next to?
OSHA standard. 29 CFR 1926.250
42. Short days: lighting and visibility 1926.56
- In winter, more work happens in the dark at the start and end of the day.
- Light work areas, ramps, runways, corridors and storage areas while work is going on.
- OSHA sets minimum lighting. General construction areas need at least 5 foot-candles. First aid stations need 30.
- Wear high-visibility clothing near equipment and traffic.
- Report burned-out or knocked-down temporary lights right away.
Ask the crew. Which part of the site is darkest at the end of the shift? Who checks the temporary lights?
OSHA standard. 29 CFR 1926.56, Table D-3
Vehicles and backing
43. Blind spots and backup alarms 1926.602(a)(9), 1926.601(b)(4)
- Earthmoving and compacting equipment with a blocked rear view needs a working backup alarm, or a spotter who signals when it's safe to back.
- Trucks and other vehicles with a blocked rear view need the same. A reverse alarm loud enough to hear over the noise, or an observer.
- Machines that run both ways, like rollers, loaders and dozers, need a working horn.
- Make eye contact with the operator before you walk near a machine.
- If you can't see the operator's eyes, the operator can't see you.
Ask the crew. Where are the blind spots on the equipment we're running this week? Who spots for trucks backing in?
OSHA standard. 29 CFR 1926.602(a)(9), 29 CFR 1926.601(b)(4)
44. Seat belts and rollovers 1926.602(a)(2), 1926.601(b)(9)
- Earthmoving equipment with rollover protection must have seat belts. Wear yours.
- Rollover protection works only if you stay inside it. The belt keeps you there.
- Motor vehicles on site need seat belts installed.
- Follow the maker's limits for slopes and loads.
- If a machine starts to tip, stay in the seat and hold on. Don't jump.
Ask the crew. Which machines here have a belt that doesn't work? Where on this site could a machine roll?
OSHA standard. 29 CFR 1926.602(a)(2), 29 CFR 1926.601(b)(9)
45. Working near traffic: vests and flaggers 1926.201(a), 1926.651(d)
- Flaggers and their warning garments follow Part 6 of the federal Manual on Uniform Traffic Control Devices (MUTCD).
- Excavation workers exposed to public traffic wear warning vests or other high-visibility garments.
- Set up traffic controls before work starts.
- Stay inside the work zone. Don't turn your back on traffic.
- Know your escape path if a vehicle comes into the zone.
Ask the crew. Where does traffic come closest to our work zone? Who on this crew is trained to flag?
OSHA standard. 29 CFR 1926.201(a), 29 CFR 1926.651(d)
Emergency and first aid
46. Emergency action plan: exits and head count 1926.35
- Know the escape routes and the meeting point for this site.
- After an evacuation, someone counts heads. Know who does it.
- Know how to report a fire or other emergency, and what the alarm sounds like.
- The plan is reviewed with you when you start, when your role changes and when the plan changes.
- Companies with 10 or fewer employees may share the plan by word of mouth instead of in writing.
Ask the crew. Where do we meet if we have to leave the site? What address do we give 911?
OSHA standard. 29 CFR 1926.35
47. First aid kits and what to do first 1926.50
- First aid supplies must be easy to get to.
- The kit is checked before each job and at least weekly. Used items get replaced.
- If no clinic or hospital is reasonably close, a person with a valid first aid certificate must be on site.
- Where 911 isn't available, post emergency numbers. Where 911 doesn't get your location automatically, post the site's latitude and longitude or other location details.
- In an emergency, make the scene safe, call 911 and give first aid if you're trained.
Ask the crew. Where is the first aid kit, and who is trained? What would you tell 911 so they can find us?
OSHA standard. 29 CFR 1926.50(c), (d) and (f)
48. Fire extinguishers: PASS 1926.150
- PASS means Pull the pin, Aim low at the base of the fire, Squeeze the handle, and Sweep side to side.
- Before you fight a fire, sound the alarm and know your way out. Don't let the fire get between you and the exit.
- If the extinguisher runs out or the fire grows, get out.
- Buildings under construction need at least one 2A extinguisher for each 3,000 square feet. Nobody should walk more than 100 feet to reach one.
- Where more than 5 gallons of flammable liquid or 5 pounds of flammable gas are in use, keep a 10B extinguisher within 50 feet.
Ask the crew. Where is the closest extinguisher to where you work? When was it last inspected?
OSHA standard. 29 CFR 1926.150(c)(1). Guidance: OSHA eTool: Fire Extinguisher Use
49. Reporting injuries and near misses 1904.35, 1904.39
- Report every work injury or illness to your foreman right away. The employer must have a reasonable way for you to report.
- You have the right to report. Your employer can't fire you or punish you for it.
- Report near misses too. A near miss shows a hazard before anyone gets hurt.
- The employer reports a work-related death to OSHA within 8 hours. An in-patient hospital stay, an amputation or the loss of an eye gets reported within 24 hours.
Ask the crew. What near miss did you see this month that nobody wrote up? Who do you tell, and how?
OSHA standard. 29 CFR 1904.35, 29 CFR 1904.39
Health
50. Manual lifting and back safety General duty clause
- Store material at power zone height, about mid-thigh to mid-chest. Then you lift less from the floor.
- Keep the load close to your body. Bend your knees and keep your back straight.
- Don't twist. Turn with your feet.
- OSHA's guidance suggests two or more people for loads over 50 pounds.
- Use carts, dollies, pallet jacks and lifts when you can.
Ask the crew. What's the heaviest thing we lift by hand on this job? What could lift it for us?
OSHA guidance. OSH Act Section 5(a)(1), OSHA eTool: Materials Handling, Heavy Lifting
51. Distracted work: phones and fatigue General duty clause
- Put the phone away while you run equipment, work at height or work near traffic.
- OSHA says long hours can raise the risk of injuries and accidents.
- Night shifts, rotating shifts and long weeks cut into sleep. Tired workers are less alert.
- Tell the foreman if you're too tired to work safely.
- Take your breaks.
Ask the crew. When does fatigue show up on this crew? What's one task here where a glance at a phone could get someone hurt?
OSHA guidance. OSH Act Section 5(a)(1), OSHA: Long Work Hours, Extended or Irregular Shifts, and Worker Fatigue
52. Mental health and suicide prevention OSHA guidance
- Construction work carries real stress. OSHA names seasonal work, demanding schedules and injuries.
- If a coworker seems off, ask how they're doing. Then listen.
- You don't have to fix it. Help them reach someone who can.
- The 988 Suicide and Crisis Lifeline is confidential and open 24/7. Call or text 988.
- Know what help your company offers, such as an employee assistance program.
Ask the crew. Who would you call if you were worried about a coworker? Where is the 988 number posted on this site?
OSHA guidance. OSHA: Preventing Suicides in Construction
Need a written safety program for your next prequal?
Answer about a dozen questions and get a program written for your trade, citing the OSHA standard each section covers. It includes a year of toolbox talks matched to your work. Free.
Printable sign-in sheet
Print one sheet for each talk. Fill in the top before the crew arrives. Pass it around at the end. The button prints only the sheet, not this page.
Toolbox talk sign-in sheet
| Company | Job site | ||
|---|---|---|---|
| Date | Start time | ||
| Topic | |||
| Presenter | Presenter signature | ||
| Hazards or questions raised | |||
| # | Name (print) | Signature |
|---|---|---|
| 1 | ||
| 2 | ||
| 3 | ||
| 4 | ||
| 5 | ||
| 6 | ||
| 7 | ||
| 8 | ||
| 9 | ||
| 10 | ||
| 11 | ||
| 12 | ||
| 13 | ||
| 14 | ||
| 15 | ||
| 16 | ||
| 17 | ||
| 18 | ||
| 19 | ||
| 20 |
Blank sign-in sheet from prequalifysubs.com/guides/toolbox-talks. Free to copy.
FAQ
Does OSHA require toolbox talks?
No OSHA standard requires a weekly toolbox talk by name. OSHA does require employers to train each worker to recognize and avoid unsafe conditions, under 29 CFR 1926.21(b)(2). Toolbox talks are a common way to deliver part of that training and to prove it happened. Many GCs also require them in the subcontract or the site safety plan.
How long should a toolbox talk be?
There is no set length. Ten minutes is enough for one topic, a quick demonstration and a few questions from the crew. If a topic needs more time, split it across two weeks or schedule full training.
How often should we hold toolbox talks?
Weekly is a common schedule, and it is the one this library is built for. Some GCs set their own schedule in the subcontract or the site safety plan. Check both, then follow the stricter rule.
Who should lead the toolbox talk?
The foreman or a lead worker usually leads it. They know the crew and the day's work. The presenter should read the talk ahead of time, know the standard it covers and be able to show the right way to do the task.
Can we give toolbox talks in Spanish or another language?
Yes. OSHA's training policy says employers must instruct workers in a language and vocabulary they understand. Give the talk in the language your crew understands best. Use a bilingual lead or a second presenter if the crew is mixed.
How long should we keep toolbox talk sign-in sheets?
OSHA does not set one retention period for toolbox talk records. A simple rule is five years. That matches how long OSHA requires you to keep the OSHA 300 log and 300A summary under 29 CFR 1904.33. Some standards and GCs ask for specific training records, so check those too.
Sources
OSHA standards, Title 29 of the Code of Federal Regulations:
- 1904.33 Retention and updating, 1904.35 Employee involvement, 1904.39 Reporting fatalities, hospitalizations, amputations and losses of an eye
- 1910.134 Respiratory protection, 1910.1200 Hazard communication and its Appendix D
- 1926.20 General safety and health provisions, 1926.21 Safety training and education, 1926.25 Housekeeping, 1926.35 Employee emergency action plans
- 1926.50 Medical services and first aid, 1926.52 Occupational noise exposure, 1926.56 Illumination, 1926.59 Hazard communication
- 1926.95 Criteria for personal protective equipment, 1926.100 Head protection, 1926.101 Hearing protection, 1926.102 Eye and face protection, 1926.103 Respiratory protection
- 1926.150 Fire protection, 1926.152 Flammable liquids, 1926.201 Signaling, 1926.250 General requirements for storage, 1926.252 Disposal of waste materials
- 1926.300 General requirements for tools, 1926.302 Power-operated hand tools, 1926.303 Abrasive wheels and tools, 1926.350 Gas welding and cutting, 1926.352 Fire prevention
- 1926.404 Wiring design and protection, 1926.416 Electrical safety-related work practices, 1926.417 Lockout and tagging of circuits
- 1926.451 Scaffolds, general requirements, 1926.453 Aerial lifts, 1926.500 Fall protection definitions, 1926.501 Duty to have fall protection, 1926.502 Fall protection systems criteria and practices, 1926.503 Fall protection training
- 1926.600 Equipment, 1926.601 Motor vehicles, 1926.602 Material handling equipment, 1926.651 Specific excavation requirements, 1926.652 Requirements for protective systems
- 1926.1052 Stairways, 1926.1053 Ladders, 1926.1153 Respirable crystalline silica, 1926.1408 Power line safety, 1926.1425 Keeping clear of the load
OSHA policy and guidance:
- OSH Act of 1970, Section 5, Duties (the general duty clause)
- CPL 02-00-124, Multi-Employer Citation Policy
- OSHA Training Standards Policy Statement, April 28, 2010
- Heat, Protecting New Workers, Heat-Related Illnesses and First Aid, Protecting Workers from the Effects of Heat
- Quick Card: Protecting Workers from Cold Stress, Winter Weather: Hazards and Precautions
- SHIB 03-24-2004, Suspension Trauma/Orthostatic Intolerance
- Silica, Crystalline, Occupational Noise Exposure
- eTool: Fire Extinguisher Use, eTool: Materials Handling, Heavy Lifting
- Long Work Hours, Extended or Irregular Shifts, and Worker Fatigue, Preventing Suicides in Construction
- National Safety Stand-Down to Prevent Falls in Construction
Other sources:
- NIOSH, Nail Gun Safety
- PHMSA, Call Before You Dig
- NUCA, Trench Safety Stand Down
- Subcontractor Safety Performance Questionnaire, a public prequalification form that asks about toolbox meetings
This guide is general information, not legal advice. Standards change, so check the current text at osha.gov. PreQualifySubs.com is not affiliated with or endorsed by OSHA.
We can make this easier
PreQualifySubs.com gives every GC one prequal link. Subs fill their profile once and reuse it for every GC. We check licenses, liens, OSHA records, insurance and references against the source, so you see a verified level instead of a stack of PDFs. Free for subs.